LM3900 PDF

LM LM LM Quad Amplifiers. General Description. The LM series consists of four independent dual input internally compensated amplifiers . Texas Instruments LM Series Operational Amplifiers – Op Amps are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for . lm are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for lm

Author: Kagakazahn Nikobei
Country: Finland
Language: English (Spanish)
Genre: Environment
Published (Last): 7 December 2012
Pages: 387
PDF File Size: 6.97 Mb
ePub File Size: 8.36 Mb
ISBN: 584-8-49295-201-8
Downloads: 85412
Price: Free* [*Free Regsitration Required]
Uploader: Nashakar

This voltage is added to the Zener voltage at the output.

A unity-gain buffer is shown at the left. Again, the high input impedance of the voltage op-amp is not obtained.

To understand this circuit, assume for simplicity that the output swings from 0 to the supply voltage V. LM pin configuration and architecture. Hello, can I use 3. Note the symbol for the Norton op-amp, that has a current source between the inputs, and an arrow on the noninverting input. This is an AC amplifier, with coupling capacitors at input and output so there is no worry about DC bias levels, which can be chosen as necessary. The first circuit to look at is the inverting amplifier, shown at the right.

LM Quad Op Amp IC | NightFire Electronics LLC

The divider supplies a current into what is effectively a unity-gain buffer to reproduce its voltage at the output. The LM is a pin DIP containing four identical op-amps, each with inverting and noninverting inputs and an output. The extremely high input resistance of the voltage or FET-input op-amp lj3900 not obtained, however. The input and feedback resistors are as with the familiar circuit, and the gain in this case should be Connect Ch 1 to the input voltage, and Ch 2 to the output.

The output terminal from each channel is connected to a single output line with a resistance not greater than K and produces a mixed audio at the output with very l,3900 noise.

In this case, the bias is about 10 x 0. In this case, the bias does not depend on the supply voltage. They also provide lm390 large output swing. The slew rate of the LM was evident in the output waveform.

Buffered, this would be an easy way to get a sine wave. Equal currents supplied to the two inputs are not amplified.

The Norton op-amp can also be used to make active filters and oscillators; see the National Semiconductors application note AN for details. Instead of a differential amplifier, the input stage is the current-differencing circuit shown at the right.

This is a very graphic illustration of Schmitt trigger operation. Connections for the LM are shown at the left. The circuit consists of 4 channel quad amplifier LM An inverting Schmitt trigger is shown at the right.

National Semiconductor

The measured values from the scope were 3. LM series amplifiers consist of four independent and internally compensated amplifiers that are designed for single and wide power supply voltage. For a 12V supply, these levels are about 7. The usual op-amp responds to a differential voltage at its inputs, but the LM responds to lm390 differential current. L3m900 C1 to C4 are the decoupling capacitors for the corresponding channels. A relaxation oscillator is shown at the left. The built in amplifier of each section amplifies every audio input separately and is fed to the output terminals.

When you test this circuit, the scope traces for input and output can be superimposed with proper setting of the gain, and the inversion is obvious. Here, the current supplied by the output is returned to the inverting input, where it flows out the k bias resistor, so the bias is positive.

Multi-channel audio mixer circuit using LM john July 27, 4 Comments. Multi channel audio mixer circuit. It supplies a current 12 – 0.

Another difference that is immediately obvious is that the inputs are one diode drop, about 0.

It relies on the diode drop at the inverting input to supply a current proportional to V bewhich is then amplified by the feedback resistor.

When the capacitor voltage reaches this level, the ouput again goes high, and the cycle repeats. C5 is the output decoupling capacitor. The hysteresis can be displayed directly lm39000 the scope, using the X-Y display. Its output swings from very near ground to a diode drop below the positive supply.

LM3900 Quad Op Amp IC

Calvert Created 10 August Last revised 19 September The input and supply voltages can be exchanged to give a noninverting circuit.

The LM can use from 4 to 36 V total supply voltage. The LM is specially useful when only a single power supply is available. I think resistors R8 and R10 should be taken out. Feedback from the output to the inverting input acts to reduce the difference current, which in normal operation is very small.

The unity-gain buffer is a special case of the noninverting amplifier, shown at the right with biasing by means of a voltage divider. Each input is connected to the inverting terminal of LM A pass transistor can be added at the output for additional current capacity the LM can be depended on only for about 20 mA when sinking current.

With the values shown, this circuit oscillated at Hz, the output swinging from near zero to