MOTOROLA GR500 REPEATER EBOOK DOWNLOAD

The Motorola GR Repeater provides the perfect solution. By making it easy to extend your two-way system to accommodate longer distances, these. NOTE: THIS IS AN ASTRON SLM POWER SUPPLY. (IN THIS CASE, THE “M” STANDS FOR MOTOROLA-. THERE ARE NO METERS ON THIS UNIT). Motorola GR VHF/UHF 40/45Watts Increase the range and capabilities of your mobile and portable radios with the GR repeater. It provides the flexibility.

Author: Zologami Malagore
Country: Central African Republic
Language: English (Spanish)
Genre: Love
Published (Last): 22 June 2005
Pages: 97
PDF File Size: 17.43 Mb
ePub File Size: 11.98 Mb
ISBN: 967-6-86316-264-8
Downloads: 7450
Price: Free* [*Free Regsitration Required]
Uploader: Tele

Motorola Radius GR500 Repeater Station Input Voltage 115/230vac

The Triad TY is a broadband audio transformer and if you use that one you won’t have to worry about that. This section covers repeqter mobile radios – see the DeskTrac Overview article in this section for additional information on the tabletop station. If you are going to be doing any upgrading, or you are converting a trunking radio to conventional, you will need a PROM-based radio which leaves out the HLN low-end 5-pin logic board and a 27C PROM chip programmed with the correct motorola gr500 repeater image.

Hold the connector ggr500 the pins facing up, the locking pin down, and the cable towards you. The holes in the PC board also have copper motorola gr500 repeater inside that connect both sides of the circuit board together. The motorola gr500 repeater of grounding fr500 pin varies with which model g5r00 microphone is used.

All MaxTrac, Radius and GM models draw about 5 milliamps when turned off standby motorola gr500 repeater for the microprocessor and about milliamps in receive squelched mode the GR series repeaters have two radios plus the control unit so they draw a small amount of additional idle current.

On a DeskTrac schematic this pin is labeled “HD”. I’m not related to that company in any way, just a very satisfied customer.

– File or directory not found.

At this point you will find that the case motorola gr500 repeater won’t go on because the plastic body of the PC connector is too tall If you try to use a standard bracket on the high power low band MaxTrac you will soon be buying the special bracket. Any Motorola prices mentioned on this page or on any page at this web site should be taken only as motorola gr500 repeater rough guideline.

It also does not have a courtesy beep.

The Motorola gr500 repeater is similar as motorola gr500 repeater as the programming mptorola the Zetron model We have no information on these or on the VR In those cases you really will want an external speaker – and motorola gr500 repeater one made for the MICOR or Syntor speaker is an excellent choice.

There were no “official” 32 channel Radius mobiles, they topped out at The 15 mL bottle size is carried by Motorola Parts as part number E Prices are changed quarterly, so use the mentioned prices only as a rough indication.

Provides trunked repeater functionality, group calling, individual selective calling, advanced interconnect calling and airtime accumulation capabilities. On this web page we are going to attempt to provide an overview of several series of radios. All Rights Reserved, including that of paper and web publication elsewhere.

Useful to CAP, Amateur and commercial. Once all of the individual pins are free then unsolder each pin motorola gr500 repeater at a time from the bottom and lift each individual pin out of the top of the board with a pair of mptorola nose pliers.

Motorola GR500 Base Station Repeater (Black)

If you are building one up, or rebuilding one do not bother with the factory coaxial cable kit that comes with the internal duplexer, it is made from some really cheap RG58 grade cable with a very loose weave.

Likewise if you are running a Maxtrac, Radius LRA or Motorola gr500 repeater as a base station in a noisy office you will motorola gr500 repeater that an external speaker makes a world of difference. If you need to remove the logic board you will need a T8 screwdriver to remove the small flat-head screws that hold the logic board’s heatsink rdpeater the side of the chassis.

There is a paper tag glued to the side of the factory crystal with an 8-digit number that contains the temperature coefficient information that needs to be typed into the RSS see this photoand naturally a new crystal will be different than motorola gr500 repeater old one, but the data on the label on your old crystal should be a good starting point. Yes, it’s a little steep, but the hard work of removing the old one IS already done These intermittent duty tabletop stations were found in shopping malls, on school campuses, motorola gr500 repeater other low-duty-cycle applications.

If you want to use a GR as a multiple-user repeater then you need motorola gr500 repeater ZR but watch the duty cycle. The GM is another matter entirely a photo motoorla a remote mount GM is in the “Adding additional channels to the GM” article in this motorola gr500 repeater. The crystals passed receiving inspection, were assembled into radios and shipped to customers. There is a table of known good microphone part numbers below.

There motorola gr500 repeater also a kit to swap the two radio chassis in a GR or GR for a single R radio this allowed a GR or GR to be narrow-banded, and the two radios that were removed could motorola gr500 repeater used elsewhere or sold. The quick and dirty solution is to remove the two female pins from the PC plug body, put heat-shrink on them individually and push each one onto the logic board pins see this photo.

So if you really have to change it, the large mass means that you need motorola gr500 repeater use a larger soldering iron, or even a soldering gun to heat each lead, then remove as much solder as possible from the joint.

Note motorola gr500 repeater the white motorola gr500 repeater case that was designed for the DeskTrac was also used for the Spectra series radios under a different marketing name. In a pinch you can connect a 2 watt resistor of any value from 8 to 22 ohms to the radio as a speaker load, and use a ohm to ohm line transformer between the radio and the test equipment.

If you motorola gr500 repeater any DeskTrac servicing that involves the Logic or RF boards in the Maxtrac radio chassis inside the DeskTrac you will want the W84 manual mentioned above as well as the DeskTrac manual since it does not cover the internals of the MaxTrac radios at all.

Again, in each case the “real” Moto part is probably the cheapest and since it’s a stock item you won’t have to wait for it.

Now mount and vr500 the new connector. The “D” series of this mic and probably some of the earlier ones is glued or solvent-welded together during manufacture and you can’t open it without serious effort. The firmware is a special chip labeled VLNA. Motorola gr500 repeater is some disagreement as to if the radio will be type accepted for narrowband service after the mod is done. Note that motprola will vibrate loose motorola gr500 repeater mobile service but this will get you by in a base station environment motorola gr500 repeater until you can locate motorola gr500 repeater proper connector The Radius product line is very broad and includes several mobiles and even more repeayer, and to specify just which Radius radio you are talking about you need to use more than just the word “Radius”.

If you are going to use a GM as a remote base you really want the 16 channel version. More key motorola gr500 repeater is on the radio keys page. Note that CAP is going to nationwide narrowband in the time frame, and some geographic areas are fully narrowband as I type this, kotorola wideband-only radios are a VERY poor investment for CAP frequencies.

The microphone cord part number HLNA for the 7 foot version plugs into the bottom of the microphone itself with a telephone style RJ-series plug.